TPS5430 Single Power Supply to Positive And Negative Power Supply Module DC5-32V

Home Arduino Module Sensor Chips About Us Item Description Features: 1: Wide range of applications 2: A variety of voltage specifications to choose from 3: Small size 4: Maximum output power 30W 5: Simple to use Module name: TPS5430 to positive and negative voltage output module Input voltage: 5.5-32V Output voltage: plus or minus 1.2V, plus or minus 3.3V, plus or minus 5V, plus or minus 9V. plus or minus 12V. plus or minus 15V (input voltage must be higher than the output voltage 2v or more) Maximum output current: positive voltage 3A, negative voltage 2A Input and output pressure difference: 2v Maximum output power: 30w Static power consumption: 16mmA (measured at 12V input,) Working frequency: 500KHZ Output ripple: 30mV at 5V. 60MV at negative 5V, (for reference only) Module weight: 20g Module size: 55*30*20mm Wiring method: transfer PIN. “Send transfer wiring, 2PIN and 3PIN each) The main features of the module are as follows: (1) The module realizes the DC-DC step-down conversion function, single power supply input, positive and negative power supply output, designed and produced according to the official data manual. (2) Input DC voltage range: 6V~32v, output DC voltage: ±5V, ±9V, ±12V or ±15V versions are optional, that is, to realize the function of converting the positive voltage of a single power supply into positive and negative voltages. The input voltage must be at least about 1V greater than the output voltage. According to the official data sheet, the input voltage can reach up to 36V in theory, but it is recommended that the input voltage should not exceed 30V. When the output is under heavy load, it is recommended that the input voltage be greater than 6V. (3) Maximum output current: 3A. According to the official data sheet, the theoretical value of the output current can reach 3A, but the chip will heat up very seriously, and the output voltage ripple will also increase, so when the power used exceeds 2OW, please add a heat sink to the TPS5430 chip for heat dissipation. Otherwise, the output voltage will be unstable, the output power ripple will become larger, and the chip may even be burned. The default output voltage of the module is ±5V, and the recommended maximum output current is 2A. (4) Ultra-low output DC voltage ripple: when the input voltage is 12V, when the output is no-load, the ±5V output voltage ripple is lower than 30mvpp; when the output is connected to a 10Ω load, the +5V output voltage terminal has low ripple At 50mVpp, the -5V output voltage ripple is lower than 75mVpp. (5) Ultra-low load regulation rate: The output load regulation rate is less than 5%. (6) Module efficiency: the greater the input voltage, the lower the power output efficiency; the power supply efficiency will also become lower as the load becomes smaller; the efficiency of the negative voltage terminal is lower than that of the positive voltage terminal. Precautions: 1 Input has no reverse connection protection, it is forbidden to reverse the positive and negative input of the input, the reverse connection will burn the module 2 The input voltage must be more than 1V higher than the output voltage Package list: 1* TPS5430 to positive and negative voltage output module 2* Terminal wire Payment Shipping Refund Payment We accept PayPal only. But we only Accept your Ebay Address ,Please Make sure it’s 100% right. Payment must be received in 5 business days of auction closing. Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. Shipping Fill your shipping info Refund All package need to wait 30 days (US only need 7-10 days) , Please take care it.Less than 30 days,we can’t take a refund . If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.