Geeetech Auto Bed Leveling Sensor 3D Touch from 3D Printer from USA

YOU MAY ALSO LIKE!!! Geeetech A10M 3D PrInter Mix Color Dual Extruder Auto-leveling Filament Detector BUY NOW GEEETECH Matte PLA Filament 1.75mm 1kg for FDM 3D Printer Frosted PLA Consumable BUY NOW GEEETECH 3D Printer Filament Silk/Shiny/Matte/Night Glow 1.75mm 1KG Per Roll BUY NOW Geeetech Luminous PLA 3D Printer Filament 1kg 1.75mm Multicolor Glow in Dark BUY NOW Geeetech ABS-Like Resin 405nm for SLA/LCD 3D Printer High Precision1KG BUY NOW 2KG GEEETECH 3D Printer PETG Filament Black 1kg/roll 1.75mm Strong Consumables BUY NOW 1KG GEEETECH PLA Filament Like Marble Stones Texture 1.75mm PLA For 3D Printer BUY NOW GEEETECH TPU 3D Filament 1KG 1.75mm White Transparent Black for 3D Printer BUY NOW Geeetech 3D Printer PLA Filament 1.75mm 1KG Colorful Filament For 3D Printer BUY NOW GEEETECH PLA/ABS/PETG/TPU 3D Printer Filament 1.75mm 1KG/roll Multi-Color Choose BUY NOW Geeetech ABS-Like/Photopolymer Resin 405nm for SLA/LCD 3D Printer Resin 1KG BUY NOW Geeetech PETG Filament 1.75mm Multi-Color Choose 1KG 3D Printer Consumables BUY NOW 3DTouch is an auto leveling sensor for 3D Printers that can precisely measure the tilt of your print surface. It can greatly improve the printing precision of your 3D Printer. 3DTouch features simple, smart and precise. It could work with nearly any kind of bed materials, such as glasses, woods, metals and so on. The main functions and controls of 3DTouch are the same as most auto bed leveling sensors, which consists of a RC servo and a micro switch, thus, 3DTouch can be used on almost every 3D printer control board. By using progressively designed solenoid and hall sensor, 3DTouch can integrate high precision in such a simple structure. To make it more user-friendly and to bring you more enjoyable printing experience we add many smart functions such as self-test, false alarm, alarm release and test mode for M119. Features: 1. Simple 3DTouch can be easily applied, since it has a small and simple structure. Gathering information & firmware setting will be an easy task, because 3DTouch works as usual auto bed leveling sensor. 2. Smart Self-test: The push pin is operated three times to test when the power is on Alarm: The LED light blinks if a problem found on a self-test or on an operation 3. High-precision 3DTouch’s Standard Deviation in repeatability is around 0.005mm, at that precise. If you choose 3DTouch, your 3D printer will be high-class masterpiece, giving you an enjoyable experience. 4. Innovative Solenoid: Ultra Power Saving On idle state, while the push-pin is whether pulled out or retracted, there are not any electric current flowing on solenoid, and standby electric current in the whole device is below 15mA on average, whereas on working state, while the pin is moving in sudden about 100ms, under 300mA flows in the device. Low power consumption even further drops joule heating, preventing from heat problem. 5. Technologies 3DTouch consists of Atmel ATtiny13A, solenoid, and a push pin. 6. wide Selection of Bed 3DTouch does not uses either optical, nor proximity (inductive/capacitive) sensor. 3DTouch is controlled by Hall Effect, providing high precision. Thus the bed material can be selected freely. 7 Optimized structure: Larger Build Size 3DTouch is a small and technology-intensive one. Build size can be set larger than other existing auto bed leveling sensor. 3DTouch uses existing RC Servo motor signal intactly, so just plug 3DTouch on the same pins after removing servo motor. Specifications: Voltage: 5V Current: 15mA Max. Current: 300mA Cable length: 150mm Net Weight: 10g Shipping weight: 25g Wiring 3-pin: Brown (-, GND), Red (+5V), Orange (control signal) 2-pin: Black (-, GND), White (Z min) Operate condition 3DTouch can be operated in the following condition. One I/O for control (PWM or Software PWM) One I/O for Z min (Z Probe) GND and +5V power Caution Additional power supply will be needed in case your board does not supply enough amperage. Electronic devices can be damaged or even destroyed if connected to wrong polarity. [wrong terminal connect to 5V(+) and GND(-)] Pulling/pushing hard on the push-pin can damage 3DTouch and make it less accurate. Fix push-pin with locking paint after reassembling or adjusting core. Do not remove or deform elastic material attached on the push-pin. Please note that: 3D touch auto leveling sensor is not plug and play; you will need to do some modification to your firmware and for some control board, you may need to do some soldering work to the connector. We have prepared the pins for you. For detailed instructions, please refer to the user manual. If you need any help, please feel free to contact us. 3DTouch auto leveling sensor User Manual Package list 1x 3DTouch Auto leveling sensor 1x 3Pin Straight Pin 1x 2Pin Straight Pin 2x Screw & Nut & Washer 2x Dupont Housing Shell 3Pin 2x Dupont Housing Shell 2Pin 3x Dupont Housing Shell 1Pin 14x Dupont Terminal 1x 10KΩ 1/8W Resistor