CH340 ESP-M2 ESP8285 ESP-M3 Wireless WIFI Development Board For ESP-12E ESP8266

Home Arduino Module Sensor Chips About Us ESP8285 ESP-M2 Strong Description: Our “DIY MORE” has plus and strong 2 series, very happy, our strong series has added a new member, ESP-M2 strong,This is a brand new design. It connects to the computer through Micro USB. For arduino IDE to downloads the program. It is very convenient! We have exported all I/Os and power supplies. It can be easily connected to your application through the DuPont cable. What is the ESP8285? ESP8285=ESP8266+1M Flash, fully compatible with ESP8266, source code can be used for transplantation The ESP-M2 strong uses the cost-effective module ESP-M2. The ESP-M2/M3 module uses the ESP8285 chip The chip integrates an enhanced Tensilica’s L106 32-bit core processor with on-chip SRAM in a smaller package. The ESP8285 has a complete Wi-Fi network function that can be used independently or as a slave to run on other host MCUs. When the ESP8285 hosts the application, it can boot directly from the external Flash. The built-in cache memory helps improve system performance and optimizes the storage system. In addition, the ESP8285 can be used as a Wi-Fi adapter only through the SPI/SDIO interface or I2C/UART port, and it can be applied to any microcontroller-based design. Built-in Tensilica L106 ultra-low-power 32-bit microprocessor, clocked at 80MHz and 160MHz, supporting RTOS, built-in TCP/IP protocol stack Built-in 1 channel 10 bit high precision ADC, peripheral interface HSPI, UART, I2C, I2S, IR Remote Control, PWM, GPIO Deep sleep maintains current of 10uA, shutdown current less than 5uA, wakes up, connects and transmits data packets within 2 ms Standby power consumption less than 1.0mW (DTIM3) Built-in 1M byte SPI Flash Package Included: 1 X ESP8285 ESP-M2 Strong CH340 WIFI Development Board for ESP-M3 ESP8266 ESP-12E ESP8285 ESP-M3 What is ESP8285? ESP8285 = ESP8266 + 1 m, bearing high temperature 125 ℃ (one for ESP8266 just 85 ℃). More importantly, the code programmed in ESP8266 can be used for ESP8285 intactly. The ESP-M3 encapsulates the high performance ESP8285 chip, which equals the ESP8266 chip plus 1 m of flash memory. The ESP825 chip is encapsulated by the extended tensilica’s L106 32-bit processor, along with SRAM. The ESP825 has a full and Wi-Fi fuction that can be used alone and alsoused as a slave with other MCU hosters that can start directly from a flash-based. In addition, the built-in high-speed buffer is an allowance for system performance. Especially, the ESP8285 can be used as a Wi-Fi adapter by SPI / SDIO and / or I2C / UART interface, when it is applied to another MCU design. Features Ultra-small size; Support serial to Wi-Fi; Wireless Transparent transmission; Long transmission distance with ultra-low power; Having a high temperature of up to 125 ° C, compared to 85 ℃ for ESP8266. Parameters SOC characteristics Built-in tensilica L106 ultra-low power 32-bit processor, the main frequency supports 80 MHz and160MHz, and rtos; Built-in protocol tcp / ip; Built-in one channel 10-bit high-precision ADC; Hanging interface: hspi, UART, I2C, I2S, IR remote controk, PWM, GPIO; Deep sleep current 10uA, the cutoff current is less than 5uA; Service, connect and transfer the data packet for 2 ms; To consume power less than 1.0 MW (DTIM3), when on stand by status; Built-in 1 m bytes for SPI flash memory. Wi-Fi Features Support 802.11 B / G / N / E / I; Station support, soft AP, soft mode AP + sta; Support for Wi-Fi Direct (P2P); Support for ccmp (CBC-MAC, calculation mode), TKIP (mic, RC4), WAPI (SMS4), WEP (RC4), CRC, etc., for hardware acceleration. P2P search, P2P Go mode / gc mode and P2P power management WPA / PA2PSK and WPS; 802.11 securitycertification: pre-certification and TSN Support 802.11n (2.4 GHz); 802.1 h / RFC1042 Encapsulation of the frame; Support seam less roaming; Support for remote updates and cloud updates (OTA); Support for Smart config functions (including Android and iOS devices). Interface Module 2 * UART; 1 * ADC; 1 * en; 1 * wake pin; 1 * hspi; 1 * I2C; 1 * I2S More than 10 * gpios Operating temperature: -40 ℃ – + 125 ℃; Module size: 26.8 mm * 16 mm Application Electronic devices; Smart Power Plug, smart light; Infant monitor; Sensor networks; Security id tags; Wireless location beacon; Home automation; Mesh networks; IP video camera; Portable Electronics; Wireless recognition location; Industrial wireless control; Package Included: 1 x ESP-M3 ESP8285 Serial Wireless Wi-Fi Transmission Module Compatible with ESP8266 Payment Shipping Refund Payment We accept PayPal only. But we only Accept your Ebay Address ,Please Make sure it’s 100% right. Payment must be received in 5 business days of auction closing. Please leave note for your special request (e.g. Colors or Size) in PayPal when you pay the order. Any special request cannot be accepted after 24 hours of payment, because most of orders will be processed instantly and same day dispatched. Shipping Fill your shipping info Refund All package need to wait 30 days (US only n eed 7-10 days) , Please take care it.Less than 30 days,we can’t take a refund . If the item is defect when you receive it or you are not satisfied with it, please return it within 14 days for a replacement or money back. But the items must be back in factory condition. Please contact us and double check the return address before you return it. If is item is defective in 12 months, you can return it to us. We will send you a new replacement after receiving the defective item.