28V 29.6V 33.6V 80A 8x 3.6V 3.7V 8S Lthium Li-PO Polymer Battery BMS PCB System

28.8V 29.6V 60V 29.4V 33.6V 80A 8S Lithium Battery Pack BMS for E-bike 8S 80A lithium Lithium Battery protection board . Applicable for 28.8V (3.6V * 8S) lithium battery & packs 29.6V (3.7V * 8S) lithium battery & packs 23.6V (4.2V * 8S) lithium battery & packs Cylindrical Lithium battery (Li-ion) Prismatic Lithium Polymer battery (Li-Po) Technical P arameters : Balanced current : 60mA (VCELL = 4.20V when ) Balanced for : 4.20 ± 0.05 V Over-charged Protection : 4.20 ± 0.05 V Over-charged delay : 55mS Over-charged release : 4.05 ± 0.05 V Over-discharged threshold : 2.90 ± 0.05 V Over-discharged delay : 5mS Over-current Protecton : 80 A Supports Max. Continuing Discharge current: 80A Max. charging current 40A Static power consumption : less than 200uA Short-circuit protection function : disconnect the load from the recovery . Size: 200mm * 110mm * 20mm (L*W*T) – with Radiating Board The main functions: Over-charged , O ver- discharged protection , short circuit protection , over-current protection , with Balancing function . The board have balancing function. So you may see a balance connector with 8 wires, below chart shows how to connect the wires onto 8 batteries to realize balancing and protection. The Positive output on Battery Pack (29.6V / 33.6V + )could connecting to charger positive pole (charger +) Battery Pack (29.6V / 33.6V – ) connecting with B- on board Chip board P- connecting to Charger Negative Pole (charger -) Chip board P- could be Negative output for charger, motor, controller Battery B+ could be Positive output for charger, motor, controller Interface Definition: 1, The charging port and the discharge port of the board are the same Positive port. “B-“ for negative Pole of the battery pack, “P-“ is negative pole for both discharging and charging. 2, “B-“ , “N-“ , “P-“ welding pad are through-hole port, hole diameter of 3.5 mm; You could use solder iron to weld the wires through the hole port Every charging port for battery are the DC needle seat forms output. “N-“ with no wiring when charging and discharging are in the same port; 3, First connect the “P-“ , “B-“ to the battery pack, then re-check with the battery voltages, Then connect the 8 wires onto the batteries, Do not connect in wrong ordering, or it will burn out the board. If you made wrong connection and reverse the board that will cause smoke, please check with every wire to be sure you are doing correct connection. check all the wires voltage with orderly, start from B- , and see if it increasing from 3.6V / 3.7V , like: ( wires with voltage ) 1 – 2 – 3 – 4 – 5 – 6 – 7 – 8 3.7V – 7.4V – 11.1V – 14.8V – 18V – 22V – 24V – 29.6V Check every voltage on the wire step by step before plug in the connector. C heck every wire and see if the orderly are correct. Because if any of the wire get a wrong order, it will get burnt. Smoke shows board already get burnt for protecting the battery being damage by wrong connection , For DIY assembling. Please make sure you are capable to do the assembling before ordering! I f you dont know how to do the connection, DONT ORDER IT! IMPORTANT!!! The BMS only use for new and consistent high drain batteries. Do not use for battery packs that mix with new & half-used, or mix with different brand battery cells. Do not use for used and imbalance battery cells. Do not use for batteries with fake capacity . Battery not including, the auction is for BMS only.